Flushing a Hydraulic System

hydraulic systems fluids_Lubrita news.jpg

Step 1
While the fluid is at operating temperature, completely drain the system, paying attention to the reservoir, all lines, cylinders, accumulators, filter housings or any area of fluid accumulation. Also, replace the filters.
Step 2
With a lint-free rag, clean the reservoir of all sludge and deposits. Make sure the entire reservoir is free of any soft or loosened paint.
Step 3
Flush the system with a lower viscosity fluid that is similar to the fluid to be used. A Reynolds number between 2.000 and 4.000 should be selected to achieve enough turbulence to remove particles from the lines. Stroke valves frequently to ensure they are thoroughly flushed. The fluid should be filtered and the flushing should continue until reaching one level beyond the system’s target cleanliness levels. For example, if the target is ISO 15/13/11, continue to flush the system until ISO 14/12/10 is reached.
Step 4
Drain the flushing fluid as hot and as quickly as possible. Replace the filters and inspect/clean the reservoir again.
Step 5
Fill the system to approximately 75 percent with the fluid to be used. Bleed/vent the pump. If the pump has a pressure relief or bypass, it should be wide open. Run the pump for 15 seconds, then stop and let it sit for 45 seconds. Repeat this procedure a few times to prime the pump.
Step 6
Run the pump for a minute with the bypass or pressure relief open. Stop the pump and let it sit for a minute. Close the bypass and permit the pump to operate loaded for no more than five minutes. Allow the relief valve to lift to confirm that it is flushed as well. Do not operate the actuators at this time. Stop the pump and let the system sit for about five minutes.
Step 7
Start the pump and operate the actuators one at a time, allowing fluid to return to the reservoir before moving to the next actuator. After operating the final actuator, shut down the system. Keep an eye on the fluid level in the reservoir. If the level drops below 25 percent, add fluid and fill to 50 percent.
Step 8
Refill the reservoir to 75 percent and run the system in five-minute intervals. At each shutdown, bleed the air from the system. Pay close attention to the system sounds to determine if the pump is cavitating.
Step 9
Run the system for 30 minutes to bring it to normal operating temperature. Shut down the system and replace the filters. Inspect the reservoir for obvious signs of cross-contamination. If any indication of cross-contamination is present, drain and flush the system again.
Step 10
After six hours of operation, shut down the system, replace the filters and sample and test the fluid.
Step 11
The sampling frequency should be increased until you are confident that the system fluid is stable. Some adherent machine deposits require tactics that are more aggressive than a high-velocity flush, so you must match the flushing tactic and strategy to the problem you are trying to resolve with the flush. Once you understand the problem within the machine that needs to be cleaned, you can then select the appropriate flushing tactic to remedy it. At this point, it should be obvious that a fluid changeout is not just a drain-and-fill operation. Care must be taken to confirm that the system is as clean as possible prior to introducing the new fluid. Most changeover procedures suggest that some of the old fluid will need to be either drained off the bottom or skimmed off the top of the reservoir after a period of time. Just because the changeover has been completed does not mean that you are “out of the woods.” Your system will need to be closely monitored for a while to make certain that the flushing was thorough. Taking the time to verify that the system is fully flushed and purged of the old fluid prior to introducing the new fluid will go a long way toward ensuring a healthier hydraulic system.

Lubrita Hydraulic Fluids, Lubricants and Technical Dada sheets You can find here: http://www.lubrita.com/product/hydraulic_oils_lubricants or contact direclty our technical department.

Flushing Tactics
There are a lot of different ways to flush out a machine. You want to match the flushing method to the flushing condition. Following are common tactics for accomplishing this: Drawdown Filtration/Separation — Contaminants or insoluble suspensions removed by filtration or separation technologies at normal flow rates. High Turbulence, High Fluid Velocity, Low Oil Viscosity — Flushing is enhanced by high turbulence flushing conditions by lower flush oil viscosity and increasing oil flow rates. High Flush Oil Temperature — This reduces viscosity, increases turbulence and increases oil solvency. Temperatures in the range of 175 to 195 degrees F are generally targeted. Cycling Flush Oil Temperature — Using heat exchangers and coolers to change temperature during flushing across a 100 degree F range helps dislodge crusty surface deposits. Pulsating Flush Oil Flow — Rapidly changing flow rates by pulsation help dislodge contaminants from nooks and crannies. Pneumatic Vibrators and Hammers — Used to break loose debris from pipe walls and connectors. Sparge Flush — Air or nitrogen is bubbled into the flush fluid to improve cleaning effectiveness. Reverse Flush Oil Flow — By changing fluid flow direction, some contaminants and surface deposits can be dislodged and washed away. Wand Flush Tool — Used for wet sumps, gearboxes and reservoirs with access hatches and clean-out ports. A wand on the end of a flushing hose is used to direct high-velocity oil flow to loosen deposits or for picking up bottom sediment. Charged Particle (Electrostatic) Separators — Some suppliers have demonstrated success at removing varnish from machine surfaces and stripping out submicron soft contaminants that can contribute to varnish and sludge. Solvent/Detergent Flush Fluid — Various solvents and detergents have been used with different degrees of success, including mineral spirits, diesel fuel, motor oils and detergent/dispersant packages. Chemical Cleaning — These are chemically active compounds,
typically caustics and acids, used to aid in the removal of organic sludge and oxide deposits. Mechanical Cleaning — This involves the use of scrapers, brushes and abrasives, typically used with solvents and other chemicals, to remove hard adherent surface deposits.

*References
Odden, Tom. (2001). “Cleaning and Flushing Basics for Hydraulic Systems and Similar Machines.” Machinery Lubrication. Ruble, Lyle. (2006). “A Guide to Converting Hydraulic Systems from Mineral Oil to Synthetic Hydraulic Fluid.” MRL Hydraulics.
*Author
Loren Green is a technical consultant with Noria Corporation, focusing on machinery lubrication and maintenance in support of Noria’s Lubrication Program Development (LPD). He is a mechanical engineer who holds a Machine Lubrication Technician (MLT) Level I certification and a Machine Lubricant Analyst (MLA) Level I certification through the International Council for Machinery Lubrication (ICML).

Welcome to Lubrita.com
International Lubrita Distributors network and World wide Oils & Lubricants online stores.

We use cookies to distinguish you from other users and ensure that we provide you with the best experience when you use our website and for the purposes of site analytics and delivering interest-based advertising.

If you consent to our use of cookies for these purposes, please close this message and continue to use this site.

I agree

Settings

Your cookie policy

Settings

You can choose not to allow some types of cookies to be set according to your privacy preferences.

Functional Cookies (necessary)

These cookies are essential for the website to function and cannot be switched off in our systems. They are usually only set in response to actions made by you, which amount to a request for services, such as establishing a session or setting your privacy preferences. These cookies do not store any personally identifiable information and they expire as soon as you leave the website.

Performance Cookies

These cookies allow us to count visits and traffic sources so we can measure and improve the performance of our site. They help us to know which pages are the most and least popular and see how visitors move around the site. We use Google Analytics for this purpose. The data collected is not shared with any other party. The information we get through the use of these cookies is anonymised and we make no attempt to identify you, or influence your experience of the site while you are visiting it. If you do not allow these cookies, we will not be able to include your visit in our statistics.

Advertising cookies

These cookies are used by us and third parties to serve ads that are relevant to your interests. We use cookies to collect data about your online activity and identify your interests so that we can provide advertising that is most relevant to you. You can opt out of receiving interest-based advertising by leaving the checkbox above empty.

I agree

I do not agree

GENERAL INFORMATION

This privacy policy determines Lubrita Europe B.V., legal entity address World Trade Center Amsterdam, Schiphol Boulevard 127, 1118 BG Schiphol, Netherlands, the e-mail address info@Lubrita.com (hereinafter referred to as the “Manager") the conditions for the processing of personal data of web siteLubrita.com visitors and other data subjects, implementation of rights of data subjects, related to the processing of personal data.

The Manager may at any time review and change the privacy policy, so we recommend that you periodically check, whether you are familiar with the relevant version of the privacy policy. The date of current version publication of the privacy policy is specified on the top of this Web page. The information about changes to the privacy policy for registered users of online stores is available on their online store account.

Personal data of the website visitors are processed in accordance with the legislation in force and ensuring the appropriate technical and organizational measures for the protection of personal data.

The Manager uses provided your personal data or with your permission collected by the Manager solely for the purposes stated in the Privacy Policy, for the purpose of handling personal data, whether for payment or free of charge, transfer to other persons, except in the cases specified in this Privacy Policy. Your personal data may be disclosed to other persons only then and only to the extent that this is necessary in order to provide you with services, to fulfill your order, and so on. For example, when purchasing goods and choosing courier delivery, your personal data required for the delivery will be disclosed to the courier service. The website contains links to non-managerial websites. The Manager is not responsible for the privacy policies of these sites, so we encourage you to be active and get familiar with the privacy policies of the websites you are directed.

WEB SITE VISITORS' PERSONAL DATA, THE USE OF COOKIES

Cookies

The website uses cookies, small text files stored on your device‘s (such as a computer, mobile phone, tablet) browser when you are browsing a Web site.

We need to use cookies on the website in order to:
ensure the proper functioning of the Web site;
ensure optimal speed and security of the Web site;
check out the Web site and its individual pages and parts, to analyze Web site traffic (the date and time of visit, browsers used, types of devices and their screen sizes), and thus continually improve the Web site, in order to better meet your needs.
Improve your login to your online store account.

Data Manager uses the following types of cookies:

Session cookies:
TITLE: _gat | FUNCTION: Designed to speed up login. | EXPIRY DATE: By the end of the visit to the site
TITLE: CMSESSIDX | FUNCTION: Designed to support the user's session | EXPIRY DATE: By the end of the visit to the site
TITLE: CookiesAgree | FUNCTION: Designed to capture visitor's acceptance of cookies. | EXPIRY DATE: By the end of the visit to the site
TITLE: CookiesLevelx | FUNCTION: Designed to determine which type of cookies the visitor has accepted. | EXPIRY DATE: By the end of the visit to the site

Permanent cookies:
TITLE: _ga | FUNCTION: Google analytics cookie to identify unique users. | EXPIRY DATE: 2 years
TITLE: _gid | FUNCTION: Google analytics cookie to identify unique users. | EXPIRY DATE: 24 hours

You can restrict or block cookies by managing your web browser settings. If you want websites to not have any cookies on your device, customize your web browser settings so that you are notified before any cookie is placed or the web browser deletes all cookies. You will need to individually adjust settings for each Internet browser for each device.

Forbidding any use of cookies or restricting their use, you may not receive the services you want or cannot use the functionality of the website.

For more information about cookies, their principles of operation and settings can be found on the website http://www.allaboutcookies.org .

Requests

The web site has a request form that you can fill out with your request to the Manager. In order to respond to your request and save proof of communication, the Manager will in any case handle the information you provided: your name, email, and request. You will not be able to contact us by submitting a request without specifying this information.

If you want the Manager's representative to be able to contact you not only by e-mail, but also by telephone, you can also provide your telephone number with the request, but you can also submit the request without the phone number.

The personal data submitted with the request and the further correspondence between you and the Manager's agent will be kept to the extent necessary for the fulfillment of a specific task and to ensure the implementation of the rights of the Manager.

ONLINE STORE CUSTOMER PERSONAL DATA

Only the registered online store users following the conditions of purchase in the e-shop can purchase goods in the manager's online store.

The personal data provided by the registration is used to fulfill the orders (to implement the Manager's legitimate interest in being able to provide evidence of communication and agreements with buyers). In addition to the personal data provided at the time of registration, the Manager also stores your purchase history for the same purpose and legal basis: the purchased goods, their price, payment method and date, delivery method and date. The email provided by registering will also be used for the purpose of direct marketing in order to provide you with information about the goods and services offered by the Manager, provided promotions and practical advices, unless you express an objection during registration to the use of your personal data for direct marketing purposes. For more information on the processing of your personal data for direct marketing purposes, you will find at DIRECT MARKETING section of the Privacy Policy.

In order to be able to fulfill your order properly, you need to provide correct personal information when registering. You can view and modify your personal details by logging in to your online store account. Please, before submitting a new order, in all cases, verify that your personal data held by the Manager are relevant and correct. The Manager assumes no responsibility if your personal data will be disclosed to other persons, you will not receive any ordered goods or experience other inconvenience due to incorrect personal data delivery or non-renewal. No property losses will be compensated due to submission of improper personal data.

The personal data of registered at online store persons will be provided to the companies providing goods delivery services, banks, which handle billing for purchased goods or services, as well as to the data processors used by the Manager (the information system administrators used by the manager, the marketing services agencies).

You can cancel your registration at online store at any time by e-mail at info@Lubrita.com. Your account will be canceled no later than within 7 business days from the receipt of the sent confirmation email and you will be notified by email on the deletion of your account.

Your personal data processed for the purpose of electronic trading is stored for 5 years since the last time shopping in the online store. If you do not buy at online store for 5 years, your account will be deleted and all personal data contained therein will be deleted. You will be notified of the intention to cancel your account at least 5 days before the account is canceled.

PERSONAL DATA OF LOYALTY PROGRAM PARTICIPANTS

You become the Loyalty client of the Manager by acquiring a Manager Loyalty card under the terms of the loyalty program.

In order to become a loyal client of the Manager and to purchase the products distributed by the Manager at a more favorable prices, you must provide the Manager with the following information by registering in the loyalty program: name, email, telephone number and address. In order to become a member of the loyalty program you do not have to submit any other personal data.

In addition to personal data submitted by you, the Manager will also process the history of purchases made through a loyalty card, such as: purchased goods, their price, the discount applied, order date, payment method and date, delivery method and date. The legal basis for the processing of personal data processed for the purpose of carrying out the loyalty program is the desire to fulfill the contract for participation in the loyalty program.

Your personal data will only be used to provide you with discounts and make direct marketing offers. If you do not wish to receive news and information on promotions for loyal customers from the Manager, check in the "additional information" box when registering that you do not agree to the processing of your personal data for direct marketing purposes.

Your personal data processed for the purpose of performing a loyalty program will be transferred to the Manager's data processors (Administrators of Information Systems used by the Manager, Marketing Agencies).

You have the right to withdraw from the loyalty program at any time by submitting an application to the e-mail address info@Lubrita.com. For processing your participation in the Loyalty Program, your personal data will be erased no later than 7 days after the confirmation about sent receipt of the email and you will be informed by email about the deletion of personal data.

DIRECT MARKETING

Each Web site visitor can subscribe to the latest news about products and services offered by the manager, promotions and practical tips (subscribe to the newsletter).

By signing up to the online store, or a loyalty program you are also included in the Database of Recipients of the Manager's Newsletter, unless you state at the time of registration that you do not wish to receive Manager's Direct Marketing Proposals.

The persons that have subscribed to the newsletter and registered at online store, so the loyalty program participants may at any time refuse Manager's newsletter by clicking on the refusal link in the newsletter or by submitting a request to the e-mail address info@Lubrita.com.

VIDEO SURVEILLANCE

Video surveillance is provided in the territory and premises of physical Manager stores, located at World Trade Center Amsterdam, Schiphol Boulevard 127, 1118 BG Schiphol, Netherlands. The image is monitored in order to ensure the security of the Manager's assets and employees. The legal basis for the processing of these data is the legitimate interest of the Manager in preventing the occurrence of damage that the Manager would suffer if he lost his property or did not ensure the safety of his employees.

Observed areas and parts of the premises are marked with visual means visible before entering the video surveillance field.

The territory and premises of the Company are monitored only in real time; we do not record and store image data, so we will not be able to satisfy your requests for access to image data.

PERSONAL DATA OF CANDIDATES FOR THE EMPLOYEES

All personal data submitted by persons wishing to employ at Manager‘s Company are administered by the Manager only for the purpose of selecting and recruiting staff, having a legitimate interest in assessing the suitability of a candidate to work as desired.

In addition to the date provided on selection and recruitment purposes by the same person who wishes to work at the Managers Company, the Manager may collect and otherwise handle other publicly available candidate data, i.e., look for information online, check candidate social networks (such as LinkedIn, Facebook, Twitter) profiles and so on.

The Manager can also apply to the former candidate's employers, indicated in the candidate's CV or social networking accounts, and request information about the candidate's qualifications, professional abilities and business characteristics.

Submitted by the candidate and independently collected data about the candidate Manager keeps 4 months since the expiry of a specific employee selection. The term for the storage of personal data is prolonged only with the individual consent of the candidate. If the consent to keep the candidate's personal data for more than 4 months after the selection is not obtained, after the expiration of this term all the personal data of the candidate (both presented by the candidate and collected by the Manager) are deleted.

INFORMATION ABOUT THE RIGHTS

All persons, whose personal data are processed by the Manager, shall have:

The right of access to their personal data, processed by the Manager.
The right to request correction of incorrect or inaccurate personal data
Registered e-shop users can access their personal data and change them by signing up to an online store account. In other cases, the right of access and request for the correction of personal data shall be implemented by submitting a written request to the Manager's office address or to e-mail address info@Lubrita.com (in case of an application signed by e-signature).

The right to demand that the Manager restrict the processing of personal data until the accuracy of personal data is verified, until it is determined whether the interests of the data subject who disagrees with the processing of personal data are superior to the Manager, as well as in cases where personal data is processed illegally, but the data subject does not agree to delete this data.
This right is implemented by providing a written request to the Manager's office address or to the email address info@Lubrita.com (in case of an application signed by e-signature). If the application is reasonable, the processing of personal data will be limited within 5 working days from the receipt of the request.

The right to data portability
This right is implemented by providing a written request to the Manager's office address or to the email address info@Lubrita.com (in case of an application signed by e-signature).If the request is reasonable, the Manager submits to you or your designated data Manager your personal data in computer-readable form no later than within 30 days of receipt of the request.

The right to disagree with the processing of personal data
Registered e-shop users and loyalty program participants express the right to oppose the processing of their personal data for direct marketing purposes by abandoning the newsletter, clicking on the refusal link or by submitting an application to the e-mail address info@Lubrita.com. In all other cases expressing disagreement with the processing of your personal data will assess whether your legitimate interest is superior to the Manager.

The right to request deletion of data
This right is implemented by providing a written request to the Manager's office address or to the email address info@Lubrita.com (in case of an application is signed by e-signature). The data Manager shall delete the relevant personal data within the 30 days following the receipt of the request or refuse to accept the application and shall state the reasons for the refusal in writing.

The right to appeal to the supervisory authority
This right may be enforced by submitting a complaint to the State Data Protection Inspectorate regarding any actions of the Manager concerning the processing of your personal data.

In cases when you implement your rights by submitting a written application to the address of the Manager's office, a copy of the identity document (passport, ID card) certified by a notary must be submitted along with the application.

CONTACTS

If you have questions regarding the privacy policy, contact us info@Lubrita.com and we will help you.

Forgot Your Password?